ROBBE Nano-Vector Instrucciones de operaciones descargar pdf (Pagina 3)

Nano-Vector ARF

Specification

Wingspan: approx. 580 mm

Overall length: approx. 510 mm

Total surface area: approx. 10 dm²

All-up weight: approx. 350 g

Total surface area loading: approx. 35 g / dm²

Dear Customer,

Congratulations on your choice of a factory-assembled model air-

craft from the robbe Modellsport range. Many thanks for placing

your trust in us.

The model can very quickly be completed ready to fly. Please read

right through these instructions and the separate information sheets

before attempting to assemble and fly the model, as this will make

it much easier to complete the tasks required.

We constantly strive to update our products to reflect the latest

developments. You can find details of technical improvements

and revised documentation on the Internet by calling up the

appropriate product description at our website: www.robbe.

com.

All directions, such as “right-hand”, are as seen from the tail of

the model, looking forward.

Notes on the power system

A brushless outrunner motor and impeller (ducted fan) are already

installed in the fuselage.

The motor is connected to the speed controller, ready for use.

To complete the power system all you have to do is connect the

LiPo flight battery.

Instructions for setting up the speed controller are included in

the Appendix to the instructions.

The radio control system

For this model you require a radio control system with at least four

channels and a delta mixer. We particularly recommend 2.4 GHz

systems.

The servos for the combined ailerons / elevators are already

installed.

The receiving system is powered by the speed controller’s integral

BEC system.

Before you check the model’s working systems, set the control

surface servos to neutral from the transmitter (transmitter sticks and

trims central).

Before flying the model always move the throttle stick to the “motor

stopped” position before switching the transmitter on. Only then

connect the flight battery.

To switch off, first disconnect the flight pack from the speed control-

ler, and only then switch the transmitter off.

When installing or setting up the receiving system compo-

nents, including the speed controller, be sure to read and

observe the instructions supplied with them.

You should also read right through the instructions and safety

information supplied with the battery pack and charger before

using these items for the first time.

Joining the components, recommended adhesives

All parts must be trial-fitted “dry” (without glue) before you

reach for the glue.

robbe Speed 1 No. 5062

Activator spray No. 5020

Please take great care to avoid excess adhesive running onto the

painted surfaces, as this will damage the finish.

Recommended accessories

Description Order No.

T-6 EX-R6308SBT 2.4 GHz

radio control system F 4106

Transmitter battery 8NIMH 2000 4548

ROXXY® POWER ZY 3S 1000mAh 30C 6911 or

2x ROXXY® POWER ZY 2S 1000mAh 30C 6910

wired in series

Connector for battery 8895

Heat-shrink tubing 4.8 D 5151

Battery charger, e.g.

POWER PEAK® Uni 7 EQ, 230V 8564

Transmitter battery charge lead F1415

Battery charge lead 8881

Velcro (hook-and-loop) tape 1713

Kit contents

- Ready-made EPO foam parts set, with decals already applied

(fuselage / wing, motor cover, canopy and cockpit)

- Separate EPO foam fins and fuselage nose-cone

- Control surface linkage hardware pack

- Factory-fitted 50 mm Ø ducted fan unit

- Factory-fitted brushless motor and speed controller

- 2 x factory-installed robbe E-COLINE 8G servos

- Multi-lingual assembly instructions

Replacement parts list

Order No. Description

25800001 Ducted fan unit 50 mm Ø

25800002 Brushless motor

25800003 Cabin

26000001 E-COLINE Servo 8G

8629 BL controller ROXXY® Control 930

Figs. 1 and 2

- Glue the fins in place, lining them up accurately

Figs. 3 and 4

- Glue the nosecone to the fuselage.

Fig. 5

- Installing the receiver: connect the servos and the speed con-

troller to the receiver, referring to the RC system instructions for

the correct channel assignment and connector pin configuration.

(the orange signal wire corresponds to the white wire used for

robbe-Futaba systems).

- Place the receiver in the fuselage and deploy the receiver

aerial(s).

Fig. 6

- Slide some heat shrink pieces onto each battery lead. Solder the

socket according to figure and insulate the solder joint with heat

shrink tubing.

Important: Do not reverse the connections of the battery to

the speed controller. Reversing the polarity will destroy the

controller immediately.

Fig. 7 and 8

Sender = Transmitter

ON = ON

Motor aus = Motor “stopped

Assembly and operating instructions

No.

2580

1 2 3 4 5 6 7 8 ... 27 28

Comentarios a estos manuales

Sin comentarios

ROBBE Nano-Vector Instrucciones de operaciones Pagina 3

Comentarios a estos manuales

Relacionado con productos y manuales para Juguetes con control remoto ROBBE Nano-Vector